Quick start

Русская версия

Your tBeacon has arrived. Let’s introduce it to your search device while the model is still on the bench, rather than somewhere in the nettles. We’ll connect the battery, make a test call and check the position. Checking the radio link takes a few minutes; the first GPS fix may take longer.

1. Prepare the beacon and battery

Check the model name on the board or packaging. Inspect the beacon, battery and antenna. Connect the battery with the correct polarity and keep its contacts from shorting.

  • Onyx2: the supplied battery plugs into a connector; normal assembly requires no soldering. GPS/GLONASS is built in. USB Type-C is provided for charging and configuration. Charge the connected battery before testing.
  • Lime: connect and charge the battery using the instructions for Lime. It has no USB port or built-in GPS; position data comes from an external GPS receiver or flight controller. You can test the radio link without that connection, but you won’t get a fresh GPS position.
  • Onyx and other hardware versions: follow the instructions for your model for battery connection, assembly and charging. Pinouts and permitted external power supplies differ between versions.

The beacon needs its own battery connected, including when configuring it from a computer. Follow the model’s instructions for any soldering, heat-shrink or protective coating, rather than a photo of a similar-looking board.

Choose your search device to see its complete set of steps below.

2. Prepare Findy

  1. Fit the antenna before making any calls and prepare the power supply. Findy S has a built-in battery and can work on its own, without a phone.
  2. Findy Lite 0.7 needs an 18650 cell with intact insulation, or USB Type-C power, for example from a power bank. The cell is sold separately. Earlier Lite versions use different power connections; check your board revision.
  3. To use a phone, install tBeacon Finder for Android or iOS. Turn on Findy and Bluetooth, open the app’s Findy section and wait for it to connect. Lite requires a phone.
  4. Add your beacon to the profile list and select it. For supported models, use automatic binding as described in the Findy manual (Russian); check the frequency and ID. On Findy S you can select a profile through the device’s own menu. The beacon’s firmware must support Findy.

Connecting your phone to Findy is the first step. Now let’s check that the beacon itself answers.

3. Turn on the beacon and make a test call

  1. Extend the beacon’s antenna and place it a few metres away from Findy.
  2. Briefly press the beacon’s button and check its startup indication.
  3. Select your beacon’s profile on Findy S, or in the app connected to Findy Lite, and send a single call.
  4. Wait for the reply and check the received beacon data. Call again and make sure the data updates after a new reply.
  5. Test the buzzer using Findy’s buzzer command, where fitted. Signal strength can help during a search, but it isn’t a distance reading in metres.

4. Check GPS and the map position

For a beacon with built-in GPS, go outside with a clear view of the sky. Keep the GPS antenna clear of the battery, metal and carbon fibre, and allow time for a fix. For Lime, check that the external GPS or flight controller is sending position data to the beacon. Then call it again with Findy.

  • Current coordinates: check the GPS status in the received data and make sure the position matches your test site.
  • Stored coordinates: the beacon may send its last known position when a fresh fix is unavailable. A new reply doesn’t necessarily mean new coordinates. Without a confirmed GPS fix, treat that position as a lead rather than the current location.
  • No coordinates: wait and call again. If GPS is unavailable, you can still search by signal.

A marker left on the map from an earlier session proves neither a working link nor a GPS fix. You need a new beacon reply and a check of its data.

5. Check shutdown and restart

For Onyx/Onyx2 and Lime, disconnect external power and hold the beacon’s button for about 5 seconds, until it switches off. For other models, check their instructions. Turn the beacon on again and repeat the single call with Findy. If you plan to use Findy’s shutdown command, test it close to the beacon beforehand. Switch the beacon back on before flying.

6. Fit it to the model and run a preflight check

  • Secure the beacon and battery, and insulate the board from conductive parts. Keep its antenna vertical where possible, away from metal and carbon fibre. Give the GPS antenna a clear view of the sky.
  • Connect external power only according to your hardware version’s instructions. Onyx, Onyx2 and Lime connectors and permitted voltages can differ.
  • Switch on the onboard electronics and make a new Findy call with the beacon installed. Check control and navigation, a fresh reply and current GPS coordinates if you’re relying on them.
  • Check the charge in the beacon, Findy and your phone if used. Test the buzzer and flash where fitted.

Ready to fly: the beacon is on, Findy receives a new reply with it fitted to the model, and any GPS position you’re relying on has been checked. A minute on the ground usually beats an evening in wet grass.

7. If the beacon doesn’t answer

  • No startup indication: check the beacon’s own battery connection and charge, its button and connectors.
  • The app won’t connect to Findy: check Findy’s power, Bluetooth and the app’s access to it. Lite needs this connection first.
  • Findy works, but the beacon doesn’t reply: check the selected profile, frequency, ID and beacon firmware compatibility.
  • A reply arrives, but no GPS position: check the view of the sky or the external GPS, wait and call again. Don’t mistake a stored position for a fresh fix.
  • The link is unreliable: inspect the antennas, move away from metal, change the devices’ positions and repeat the test in the open.

If the test fails, find the cause before flying. Your first real search is a poor time to discover how the settings work.

8. Where to go next

2. Prepare your radio

  1. Set receive and transmit to the beacon’s frequency. The factory setting is 433.075 MHz, narrow FM (NFM), with no repeater offset.
  2. For the factory calling tone, disable transmit and receive CTCSS/DCS. If the beacon’s settings have been changed, use its actual frequency and tone.
  3. Find the 1750 Hz tone burst function in your radio’s manual. Pressing PTT without the tone won’t call the beacon. On many Baofeng UV-5R versions, press PTT first, then A/B; some use PTT and BAND. Check the combination for your radio.

The calling tone is audio sent by the radio, not its operating frequency. “1750” and “433.075” belong in different settings.

3. Turn on the beacon and make a test call

  1. Extend the beacon’s antenna and place it a few metres away from the radio.
  2. Briefly press the beacon’s button. Check its startup indication; with standard settings, the radio receives a greeting and battery voltage report.
  3. Transmit the calling tone (1750 Hz by default) for about 4 seconds. This suits the factory listening interval of 3 seconds. If that interval has been increased, hold the tone for slightly longer than the configured interval.
  4. Release both the tone control and PTT to hear the reply. The beacon reports the calling signal level, followed by search tones and coordinates as enabled in its settings. The buzzer and flash activate when the received signal exceeds their configured threshold.
  5. Wait for the reply to finish, then call again and check that the beacon answers. The signal reading, including “99”, is not a distance in metres.

4. Receive and check the GPS coordinates

For a beacon with built-in GPS, go outside with a clear view of the sky. Keep the GPS antenna clear of the battery, metal and carbon fibre, and allow time for a fix. For Lime, check that the external GPS or flight controller is sending position data to the beacon. Then call again.

  • Current coordinates: GPS has acquired a position and the reported location matches your test site.
  • Stored coordinates: three short bell-like sounds before spoken coordinates warn that the position may be out of date. This is somewhere the beacon has been before: a useful lead, but no guarantee of the crash location.
  • No coordinates: GPS hasn’t acquired a fix or position data is unavailable. The radio link may still work without GPS, allowing you to search by signal.

Write down both coordinates and enter them into a navigation app using the same format as the beacon. Check the signs and the order of latitude and longitude, then make sure the position matches your test site.

5. Check shutdown and restart

For Onyx/Onyx2 and Lime, disconnect external power and hold the beacon’s button for about 5 seconds, until it switches off. For other models, check their instructions. Turn the beacon on again and call it with the radio. Test contactless shutdown beforehand using your model’s instructions; availability and settings vary by version. Switch the beacon back on before flying.

6. Fit it to the model and run a preflight check

  • Secure the beacon and battery, and insulate the board from conductive parts. Keep its antenna vertical where possible, away from metal and carbon fibre. Give the GPS antenna a clear view of the sky.
  • Connect external power only according to your hardware version’s instructions. Onyx, Onyx2 and Lime connectors and permitted voltages can differ.
  • Switch on the onboard electronics and call the installed beacon with the radio. Check control and navigation, an audible reply and current GPS coordinates if you’re relying on them.
  • Check the charge in the beacon and radio, and test the buzzer and flash where fitted.

Ready to fly: the beacon is on, answers a radio call when fitted to the model, and any GPS position you’re relying on has been checked. A minute on the ground usually beats an evening in wet grass.

7. If the beacon doesn’t answer

  • No startup indication: check the beacon’s own battery connection and charge, its button and connectors.
  • The radio is silent: check receive and transmit frequencies, the calling tone and call length. Release PTT after calling. Open the squelch; it may be hiding a weak reply.
  • A reply arrives, but no GPS position: check the view of the sky or the external GPS, wait and call again. Don’t mistake a stored position for a fresh fix.
  • The link is unreliable: inspect the antennas, move away from metal, change the devices’ positions and repeat the test in the open.

If the test fails, find the cause before flying. Your first real search is a poor time to discover how the settings work.

8. Where to go next


Related Articles

Docs

tBeacon documentation and manual

Read More

FAQ

Frequently Asked Questions

Read More

Related Products

tBeacon Lime

tBeacon Lime

tBeacon Lime radio beacon

$59.90

tBeacon Onyx 2

tBeacon Onyx 2

tBeacon Onyx 2 radio beacon with embedded GPS

$75.22